Inovonics EN1224-ON Bedienungsanleitung PDF herunterladen

EN1224/EN1224-ON EchoStream

Multiple-Condition Pendant Transmitter

Installation Instructions - 05606D

1 Overview

The EN1224 is a four-button, multi-condition pendant transmitter.

The EN1224 must be used with an EchoStream EN4000 of EN4200

serial receiver, or with the EN6040 network coordinator. In addition,

the application controller (e.g. control panel) must be designed to

accept the multiple conditions.

1.1 Inovonics Wireless Contact Information

If you have any problems with this procedure, contact Inovonics

Wireless technical services:

• E-mail: [email protected]

• Phone: (800) 782-2709

1.2 EN1224/EN1224-ON Components

Figure 1 EN1224/EN1224-ON components

2 Installation and Startup

2.1 Install/Replace the Battery

1. Pry the housing apart at either end and pull the two halves

apart.

2. If replacing a battery, remove the old battery.

3. Install the new battery.

4. Press the Reset button to initialize the transmitter.

2.2 Select the Frequency Band

EchoStream products are able to use a range of radio frequencies,

and must be configured for your geographic area. To configure the

transmitter:

1. Pry the housing apart at either end and pull the two halves

apart.

2. Place a selection jumper on the appropriate frequency band

selection pins.

• Leave the jumper off the pins to set the frequency range to

902-928 MHz for North America.

• Place the jumper on the bottom two pins, marked NZ, to set

the frequency range to 921-928 MHz for New Zealand.

• Place the jumper on the top two pins, marked AU, to set the

frequency range to 915-928 MHz for Australia.

3. Press the Reset button to complete configuration.

Caution: When pressing the Reset button, make sure you don’t

also touch the frequency band selection pins. Touching the

frequency band selection pins while pressing the Reset button can

inadvertently set the pendant to the wrong frequency band.

2.3 Register the Transmitter

The transmitter must be registered with the system in order to be

monitored and supervised. The transmitter will send a check-in

message to the serial receiver or network coordinator.

Pendants using the 868MHz frequency range for Europe will send a

check-in message every 12 minutes; all other transmitters will send

a check-in message every three minutes.

Each pendant has a unique factory-programmed identification

number. Refer to the control panel’s installation instructions for

details on registering a transmitter.

1. When prompted to reset transmitter, press and release the

Reset button.

2. Replace the cover.

3 Operation

Caution: The EchoStream system should be tested regularly to

ensure operation. To test the system, activate each of the

transmitter’s conditions and ensure an appropriate response.

3.1 Activating Conditions

The transmitter can send up to ten conditions. The conditions will

depend on the application, as will the response. The application

controller must be designed to recognize simultaneous messages.

The EN1224 and EN1224-ON require the use of an Inovonics serial

receiver, and cannot currently be used with an Inovonics add-on

receiver.

Condition signals are transmitted multiple times and are indicated

by the blinking transmission LED. Inovonics recommends you test

the transmitter regularly.

4 Specifications

Specifications Typical battery life:

3-5 years Battery type (BAT608): Panasonic CR2 or equivalent

Operating environment 0 to 60°C (32 to 140°F), noncondensing

Note: Specifications and data are subject to change without notice.

A Reset button B Frequency band selection pins

C Battery

Printing Instructions

1. Print Duplex

2. Align and orient back page to match front

page.

3. Cut on dashed line

4. Fold cutsheet in half along the 8.5" axis.

1 2

Inhaltsverzeichnis

Seite 1 - EN1224/EN1224-ON EchoStream

Seite 2 - 7 Warranty and Disclaimer

Verwandte Modelle: EN1224

Kommentare zu diesen Handbüchern

Keine Kommentare

Inovonics EN1224-ON Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Kommunikation Inovonics EN1224-ON herunter. Inovonics EN1224-ON User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: EN1224

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kommunikation Inovonics EN1224-ON