Inovonics EE4216MR Bedienungsanleitung PDF herunterladen

EE4216MR EchoStream® Receiver

Installation and Operation Manual - 05395I

1 Overview

Inovonics EchoStream technology is designed to minimize dead spots in transmission

areas using diversity reception and advanced signal processing. The EE4216MR

receiver allows you to add up to 16 transmitters and six outputs to any application.

The EE4216MR is compliant with:

• EN50131-1

• Security Grade 2

• Environmental Class II

1.1 Inovonics Wireless Contact Information

If you have any problems with this procedure, contact Inovonics Wireless technical

services:

• E-mail: support@inovonics.com

• Phone: (800) 782-2709; (303) 939-9336

1.2 EE4216MR Front Panel

Figure 1 Receiver front panel

Up Button Scrolls the display up.

Down button: Scrolls the display down.

Back button: Returns display to the previous menu, or, when entering information in

the display, returns to the last character entered.

Enter button: Selects the currently displayed menu item. If in normal operating mode,

sets the unit to menu mode.

LCD Display: Shows status, event log and programming information.

Note: The EE4216MR LCD will only display information when an authorized password

has been entered.

1.3 EE4216MR Internal Components

Figure 2 EE4216MR internal components

1.4 EE4216MR LEDs

Note: The EE4216MR operation LEDs are only visible when the cover is removed.

Output LED: Lights when any output is active.

Fault LED: Lights when any transmitter is sending a fault condition.

Power LED: Lit when receiving power.

Decode LED: Flashes when any recognizable transmission is received. This LED is

only visible with the cover removed.

2 Installation and Startup

2.1 Connect Power Cabling

Before beginning startup, you will need to connect power to the receiver. To connect

power to the receiver:

Caution: Graded application must use the cabling knockout on the back of the

housing.

1. Connect power cabling to the Vs and GND connections.

• Power source should be 11-14 VDC. Power supply must be unswitched,

uninterrupted, and regulated.

2.2 Enable EchoStream Select

To meet ETSI requirements, Inovonics has developed a new line of EE 868MHz-only

products. These new 868MHz-only products are compatible with older systems that

include EchoStream Select products. If you are using any ES products in your current

system, you will need to enable EchoStream Select compatibility on this new 868MHz-

only product.

To enable/disable EchoStream Select compatibility:

1. To enable compatibility with ES products, place a selection jumper on the ES

selection pins.

Note: Selection jumpers are included in the EE4216MR hardware packet.

2. If no ES products are used in your system, remove the selection jumper from the

ES selection pins.

3. Reset the receiver or cycle power.

2.3 Enter Password

There are three levels of EE4216MR user. Only the level 2 authorized user and level 3

authorized installer are able to access the I

NSTALL & SERVICE menu.

Level 2 authorized user access: A level 2 authorized user has the ability to view

system status indicators and enter system test mode in the I

NSTALL & SERVICE menu.

A level 2 user does not have the ability to change receiver parameters or perform

receiver functions (signal strength, test, register points, etc.). For more information on

system test mode, see “System Test Mode” on page 3.

Note: The default level 2 authorized user password is 3446.

Level 3 authorized installer access: A level 3 authorized installer has the ability to

access all I

NSTALL & SERVICE menus. A level 3 authorized installer can also view

receiver system status indicators as well as change receiver system parameters and

perform all receiver functions.

Note: The default level 3 authorized installer password is 1234.

During normal operation there is no visual indication of system status or activity on the

front display of the EE4216MR receiver. Unless the level 2 authorized user or the level

3 authorized installer enters a valid password, the LCD will remain completely blank.

To enter either the level 2 authorized user or the level 3 authorized installer password:

1. Press any button; P

ASSWORD displays.

2. Use the Up and Down buttons to scroll through the first numeral; press Enter to

select.

3. Repeat step 2 for each numeral in the password.

4. When all numerals in the password have been entered, press Enter to submit the

password.

2.4 Select Display Language

On initial startup you will need to select the display language. Once selected, the

language will be maintained unless changed using the C

HANGE LANGUAGE option in

the I

NSTALL & SERVICE menu. To select the display language, see “Select Language”

on page 3.

2.5 Navigate to the Install & Service Menu

There are three main menus: POINT STATUS, INSTALL & SERVICE and EVENT LOG. The

INSTALL & SERVICE menu is used to program outputs, select language, change

password, view the signal strength, delete points, register transmitters, and setup

points for any of the programmed points.

Note: If changing programming for a point that already has a transmitter registered to

it, there is no need to re-register the transmitter. Changes to point programming are

automatically assigned to the transmitter registered to that point.

To access the I

NSTALL & SERVICE menu:

1. From the R

EADY prompt, press the Enter button to access the receiver’s three

main menus.

2. Use the Up and Down buttons to navigate to the the I

NSTALL & SERVICE menu;

press the Enter button.

2.6 Setup Point

1. From the INSTALL & SERVICE menu, press Enter at the SETUP POINT prompt.

2. Use the Up/Down buttons to scroll through the points; press the Enter button to

select a point.

•T

X REGISTR’D displays if a transmitter or repeater is currently registered to this

point; T

X NOT REGSTR’D displays if no transmitter is registered to this point.

3. Press Enter to setup the point. The following setup options are available:

Supervision Time: Sets time limit on missing transmitter reporting.

• The valid range is 0 to 99 hours. The default is 30 minutes. Selecting 0 turns off

supervision.

A Up button B Down button C Back button D Enter button E LCD display

A Housing release tabs B Power connections C Operation LEDs

D Output terminals E Tamper output F Clear to set output

G Jam output H Reset input I EchoStream Select pins

1 2 3 4

Inhaltsverzeichnis

Seite 1 - EE4216MR EchoStream® Receiver

Seite 2 - 2.10 CTS Type

Seite 3 - 4 Operation

Seite 4 - 7 Specifications

Kommentare zu diesen Handbüchern

Keine Kommentare

Inovonics EE4216MR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Empfänger und Verstärker Inovonics EE4216MR herunter. Inovonics EE4216MR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Empfänger und Verstärker Inovonics EE4216MR